Maximum

SCPI Commands :

READ:WLAN:MEASurement<Instance>:MEValuation:TRACe:SFLatness:MIMO:RXANtenna<n>:STReam<s>:SEGMent<seg>:MAXimum
FETCh:WLAN:MEASurement<Instance>:MEValuation:TRACe:SFLatness:MIMO:RXANtenna<n>:STReam<s>:SEGMent<seg>:MAXimum
CALCulate:WLAN:MEASurement<Instance>:MEValuation:TRACe:SFLatness:MIMO:RXANtenna<n>:STReam<s>:SEGMent<seg>:MAXimum

class MaximumCls

Maximum commands group definition. 3 total commands, 0 Subgroups, 3 group commands

calculate(start: float = None, count: float = None, decimation: float = None, rxAntenna=RxAntenna.Default, stream=Stream.Default, segment=Segment.Default) → List[ResultStatus2]

# SCPI: CALCulate:WLAN:MEASurement<Instance>:MEValuation:TRACe:SFLatness:MIMO:RXANtenna<n>:STReam<s>:SEGMent<seg>:MAXimum
value: List[enums.ResultStatus2] = driver.multiEval.trace.spectrFlatness.mimo.rxAntenna.stream.segment.maximum.calculate(start = 1.0, count = 1.0, decimation = 1.0, rxAntenna = repcap.RxAntenna.Default, stream = repcap.Stream.Default, segment = repcap.Segment.Default)

Return the spectrum flatness traces for Rx antenna <n>, stream <s>, and segment <seg> for true MIMO measurements and bandwidths with two segments (80+80 MHz) . The results of the current, average, minimum and maximum traces can be retrieved. The values described below are returned by FETCh and READ commands. CALCulate commands return limit check results instead, one value for each result listed below.

Use RsCmwWlanMeas.reliability.last_value to read the updated reliability indicator.

param start:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param count:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param decimation:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param rxAntenna:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘RxAntenna’)

param stream:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Stream’)

param segment:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Segment’)

return:

spec_flat_trace_segment_tx: float Comma-separated list power level, one value per subcarrier (including data and pilot subcarriers) The number of subcarriers depends on the WLAN standard, channel bandwidth and mode, see Table ‘OFDM subcarriers’. Unit: dB

fetch(start: float = None, count: float = None, decimation: float = None, rxAntenna=RxAntenna.Default, stream=Stream.Default, segment=Segment.Default) → List[float]

# SCPI: FETCh:WLAN:MEASurement<Instance>:MEValuation:TRACe:SFLatness:MIMO:RXANtenna<n>:STReam<s>:SEGMent<seg>:MAXimum
value: List[float] = driver.multiEval.trace.spectrFlatness.mimo.rxAntenna.stream.segment.maximum.fetch(start = 1.0, count = 1.0, decimation = 1.0, rxAntenna = repcap.RxAntenna.Default, stream = repcap.Stream.Default, segment = repcap.Segment.Default)

Return the spectrum flatness traces for Rx antenna <n>, stream <s>, and segment <seg> for true MIMO measurements and bandwidths with two segments (80+80 MHz) . The results of the current, average, minimum and maximum traces can be retrieved. The values described below are returned by FETCh and READ commands. CALCulate commands return limit check results instead, one value for each result listed below.

Use RsCmwWlanMeas.reliability.last_value to read the updated reliability indicator.

param start:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param count:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param decimation:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param rxAntenna:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘RxAntenna’)

param stream:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Stream’)

param segment:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Segment’)

return:

spec_flat_trace_segment_tx: float Comma-separated list power level, one value per subcarrier (including data and pilot subcarriers) The number of subcarriers depends on the WLAN standard, channel bandwidth and mode, see Table ‘OFDM subcarriers’. Unit: dB

read(start: float = None, count: float = None, decimation: float = None, rxAntenna=RxAntenna.Default, stream=Stream.Default, segment=Segment.Default) → List[float]

# SCPI: READ:WLAN:MEASurement<Instance>:MEValuation:TRACe:SFLatness:MIMO:RXANtenna<n>:STReam<s>:SEGMent<seg>:MAXimum
value: List[float] = driver.multiEval.trace.spectrFlatness.mimo.rxAntenna.stream.segment.maximum.read(start = 1.0, count = 1.0, decimation = 1.0, rxAntenna = repcap.RxAntenna.Default, stream = repcap.Stream.Default, segment = repcap.Segment.Default)

Return the spectrum flatness traces for Rx antenna <n>, stream <s>, and segment <seg> for true MIMO measurements and bandwidths with two segments (80+80 MHz) . The results of the current, average, minimum and maximum traces can be retrieved. The values described below are returned by FETCh and READ commands. CALCulate commands return limit check results instead, one value for each result listed below.

Use RsCmwWlanMeas.reliability.last_value to read the updated reliability indicator.

param start:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param count:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param decimation:

numeric For the optional query parameters start, count and decimation, see ‘Trace sub-arrays’.

param rxAntenna:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘RxAntenna’)

param stream:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Stream’)

param segment:

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Segment’)

return:

spec_flat_trace_segment_tx: float Comma-separated list power level, one value per subcarrier (including data and pilot subcarriers) The number of subcarriers depends on the WLAN standard, channel bandwidth and mode, see Table ‘OFDM subcarriers’. Unit: dB